ISO 23429 PDF

Gauging of hexagon sockets (ISO ); German version EN ISO ISO Gauging of hexagon sockets. standard by International Organization for Standardization, 01/15/ View all product details. Buy NF EN ISO Gauging Of Hexagon Sockets from SAI Global.

Author: Nesar Kajilkree
Country: Mongolia
Language: English (Spanish)
Genre: Personal Growth
Published (Last): 4 October 2012
Pages: 167
PDF File Size: 10.46 Mb
ePub File Size: 9.73 Mb
ISBN: 259-4-18829-407-4
Downloads: 70607
Price: Free* [*Free Regsitration Required]
Uploader: Vudoran

Hexagon socket button head screw ISO – M12 40 – In accordance with Adobe’s licensing policy, this file may be printed or viewed but shall not be edited unless the izo which are embedded are licensed to and installed on the computer performing the editing.

Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic lso mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or ISO’s member body in the country of the requester.

Endorsement notice The text of ISO Symbols and designations of dimensions are defined in ISO NOTE Particular attention is drawn to the note in Table 2 and to Table 3 concerning the limitation on ultimate tensile load. If, in special cases, specifications other than those listed in this International Standard are required, they should be selected from existing International Standards, e. For dated references, only the edition cited applies. ISO shall not be held responsible for identifying any or all such patent rights.

Product Details

The work of preparing International Standards is normally carried out through ISO technical committees. Acceptability Acceptance procedure is covered in ISO The main task of technical committees is to prepare International Standards. Intermediate nominal lengths according to ISO are permissible. Adobe is a trademark of Adobe Systems Incorporated. For undated references, the latest edition of the referenced document including any amendments applies.

TOP Related  BD7902FS PDF

Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. Every care has been taken to ensure that the file is suitable for use by ISO member bodies.

EN ISO 内六角平圆头螺钉 – MBA智库文档

This third edition cancels and replaces the second edition ISO Table 3 — Minimum ultimate tensile loads for hexagon socket button head screws of the values specified in ISO Thread Property class 8. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. Requirements for non-electrolytically applied zinc flake coatings are covered in ISO Alternative form of socket permissible For broached sockets which sio at the maximum 234429 of size the overcut resulting from drilling shall not exceed of the length of any flat of the socket which is.

Draft International Standards adopted by the technical committees are circulated to the member bodies for voting.

ISO – Gauging of hexagon sockets

Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the Central Secretariat or to any Ido member.

In downloading this file, parties accept isoo the responsibility of not infringing Adobe’s licensing policy. Technical Committee Mechanical fasteners Publisher and printing: Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation parameters were optimized for printing. All rights reserved; No part of this publication may be reproduced or utilized in any form or by any means — elec- tronic, mechanical, photocopying or any other data carriers without prior permission from ON!

TOP Related  JOVAN DERETIC ANTICKA SRBIJA PDF

International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. They shall nevertheless meet the other material and property requirements for the respective property class specified in ISO This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by Julyand conflicting national standards shall be withdrawn at the latest by July In addition, when full-size screws are loaded using the type of testing fixture illustrated in ISOthey shall withstand, without fracture, the minimum ultimate tensile loads given in Table 3.

A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the Central Secretariat has the same status as the official versions. In the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below.