ASTM C128 PDF

Referenced Documents. ASTM Standards: C 29/C 29M Test Method for Bulk Density (“Unit Weight”) and Voids in Aggregate2. C 70 Test Method for Surface. ASTM Designation: C 1. SCOPE. This method covers the determination of bulk and apparent specific gravity, 23/23ºC. (/ºF), and absorption. Qty. Model, Description. 1, Choose One: HBA, Adam Core balance g x g, V 60Hz. HBA.4F, Adam Core balance g x g, V 50/.

Author: Nakazahn Gardagal
Country: Czech Republic
Language: English (Spanish)
Genre: Spiritual
Published (Last): 8 September 2008
Pages: 365
PDF File Size: 5.85 Mb
ePub File Size: 16.13 Mb
ISBN: 487-6-30939-818-1
Downloads: 41791
Price: Free* [*Free Regsitration Required]
Uploader: Masida

The values obtained for absorption by other test methods will be different than the values obtained by the prescribed h soak, as will the relative density specific gravity SSD. Link to Active This link will always route to the current Active version of the standard.

It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. Historical Version s – view previous versions of standard. It is zstm responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

This value is not widely used in construction aggregate technology. Referenced Documents purchase separately The documents listed below are referenced within the subject standard but are not provided as part of the standard. Aggregates mined ast, below the water table commonly have a moisture content greater than the absorption determined by this test method, if used without opportunity to dry prior to use.

TOP Related  LS3408 PDF

Active Risk Management

For an aggregate that has been in contact with water and that has free moisture on the particle surfaces, the percentage of free moisture is determined by deducting the absorption from the total moisture content determined by Test Method C by drying. Referenced Documents purchase separately The documents listed below are referenced within the subject standard but are not provided as part of the standard.

The SSD relative density and absorption are determined after soaking the aggregate in water for a prescribed duration. The SSD density, SSD relative density, and absorption are determined after soaking the aggregate in water for a prescribed duration.

It is also expressed as the ratio of the density of the aggregate particles to the density of water. Conversely, some aggregates that have not been continuously maintained in a moist condition until used are likely to contain an amount of absorbed moisture less than the h soaked condition. These notes and footnotes excluding those in tables and figures shall not be considered as requirements of this test method.

Link to Active This link will always route to the current Active version of the standard. Likewise, relative density specific gravitya dimensionless quality, is expressed as OD, SSD, or as apparent relative density apparent specific gravity. Relative density specific gravity SSD is used in the determination of surface moisture on fine aggregate by displacement of water in Test Method C The laboratory standard for absorption is that obtained after submerging dry aggregate for a prescribed period of time.

TOP Related  SAADAT HASSAN MANTO SHORT STORIES PDF

The test results for density shall be reported in either SI units or inch-pound units, as appropriate for the use to be made of the results. Work Item s – proposed revisions of this standard. The OD density and OD relative density are determined after drying the aggregate.

ASTM C Standard

No other units of measurement are included in this standard. Relative density specific gravity SSD is used if the aggregate is in a saturated surface-dry condition, that is, if its absorption has been satisfied. c12

Alternatively, the relative density specific gravity OD ast, used for computations when the aggregate is dry or assumed to be dry. The relative density specific gravitya dimensionless quality, is expressed as oven-dry ODsaturated-surface-dry SSDor as apparent relative density specific gravity.

Active view current version of standard. Work Item s – proposed revisions of this standard.

The OD relative density is determined after drying the aggregate. These notes and footnotes excluding those in tables and figures shall not be considered as requirements of this test method.